Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (21.14 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 2.95 / 3 ] Optimization level option is correctly used
[ 2.95 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g and -fno-omit-frame-pointer
-g option gives access to debugging informations, such are source locations. -fno-omit-frame-pointer improve the accuracy of callchains found during the application profiling.
[ 2.95 / 3 ] Architecture specific option -x SAPPHIRERAPIDS is used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.05 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (67.03%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (27.05%), representing an hotspot for the application
[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (58.08%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 3 ] Less than 10% (0%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (8.95%) lower than cumulative innermost loop coverage (58.08%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0%) is spend in Libm/SVML (special functions)
[ 2 / 2 ] Less than 10% (0%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 428 - libparcsr_ls.so | Execution Time: 27 % - Vectorization Ratio: 100.00 % - Vector Length Use: 43.75 % | |
| ►Data Access Issues | 14 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 3 issues ( = arrays) costing 2 points each | 6 |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Inefficient Vectorization | 4 | |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Loop 149 - libseq_mv.so | Execution Time: 6 % - Vectorization Ratio: 100.00 % - Vector Length Use: 43.75 % | |
| ►Data Access Issues | 14 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 3 issues ( = arrays) costing 2 points each | 6 |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Inefficient Vectorization | 4 | |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Loop 161 - libseq_mv.so | Execution Time: 6 % - Vectorization Ratio: 100.00 % - Vector Length Use: 43.75 % | |
| ►Data Access Issues | 14 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 3 issues ( = arrays) costing 2 points each | 6 |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Inefficient Vectorization | 4 | |
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 1 issues (= instructions) costing 4 points each. | 4 |
| ►Loop 427 - libparcsr_ls.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 424 - libparcsr_ls.so | Execution Time: 2 % - Vectorization Ratio: 34.78 % - Vector Length Use: 16.85 % | |
| ►Loop Computation Issues | 10 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 1 issues (= instructions) costing 4 points each. | 4 |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 23 | |
| ○ | [SA] Too many paths (17 paths) - Simplify control structure. There are 17 issues ( = paths) costing 1 point each with a malus of 4 points. | 21 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 4 issues (= instructions) costing 1 point each. | 4 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 23 | |
| ○ | [SA] Too many paths (17 paths) - Simplify control structure. There are 17 issues ( = paths) costing 1 point each with a malus of 4 points. | 21 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Inefficient Vectorization | 4 | |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 4 issues (= instructions) costing 1 point each. | 4 |
| ►Loop 215 - libseq_mv.so | Execution Time: 1 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 2 issues ( = arrays) costing 2 points each | 4 |
| ►Loop 182 - libseq_mv.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Control Flow Issues | 11 | |
| ○ | [SA] Too many paths (5 paths) - Simplify control structure. There are 5 issues ( = paths) costing 1 point each with a malus of 4 points. | 9 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 11 | |
| ○ | [SA] Too many paths (5 paths) - Simplify control structure. There are 5 issues ( = paths) costing 1 point each with a malus of 4 points. | 9 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 148 - libseq_mv.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 141 - libseq_mv.so | Execution Time: 0 % - Vectorization Ratio: 14.84 % - Vector Length Use: 14.12 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 6 | |
| ○ | [SA] Several paths (4 paths) - Simplify control structure or force the compiler to use masked instructions. There are 4 issues ( = paths) costing 1 point each. | 4 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 21 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 24 | |
| ○ | [SA] Several paths (4 paths) - Simplify control structure or force the compiler to use masked instructions. There are 4 issues ( = paths) costing 1 point each. | 4 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Inefficient Vectorization | 1 | |
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ►Loop 160 - libseq_mv.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |