Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (972.61 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3.00 / 3 ] Optimization level option is correctly used
[ 3.00 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g and -fno-omit-frame-pointer
-g option gives access to debugging informations, such are source locations. -fno-omit-frame-pointer improve the accuracy of callchains found during the application profiling.
[ 3.00 / 3 ] Architecture specific option -march=sapphirerapids is used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (99.68%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (7.32%), representing an hotspot for the application
[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (99.62%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 3 ] Less than 10% (0%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.06%) lower than cumulative innermost loop coverage (99.62%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0%) is spend in Libm/SVML (special functions)
[ 2 / 2 ] Less than 10% (0%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
| Loop ID | Module | Analysis | Penalty Score | Coverage (%) | Vectorization Ratio (%) | Vector Length Use (%) |
|---|---|---|---|---|---|---|
| ►589 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 9 | 7.32 | 10.59 | 13.82 |
| ○ | [SA] Too many paths (5 paths) - Simplify control structure. There are 5 issues ( = paths) costing 1 point each with a malus of 4 points. | 9 | ||||
| ○ | Warning! Some static analysis are missing because the loop has too many paths. Use a higher value for --maximal_path_number option. | 0 | ||||
| ►276 | exec | Inefficient vectorization. | 98 | 6.42 | 100 | 100 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 24 issues (= instructions) costing 4 points each. | 96 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►233 | exec | Inefficient vectorization. | 4 | 6.25 | 100 | 100 |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►220 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 654 | 5.66 | 99.21 | 98.12 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 112 issues (= instructions) costing 4 points each. | 448 | ||||
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 35 issues (= instructions) costing 4 points each. | 140 | ||||
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 14 issues ( = indirect data accesses) costing 4 point each. | 56 | ||||
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BROADCAST) - Simplify data access and try to get stride 1 access. There are 4 issues (= instructions) costing 1 point each. | 4 | ||||
| ○ | [SA] Inefficient vectorization: use of masked instructions - Simplify control structure. The issue costs 2 points. | 2 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►273 | exec | Inefficient vectorization. | 98 | 5.33 | 100 | 100 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 24 issues (= instructions) costing 4 points each. | 96 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►157 | exec | Inefficient vectorization. | 34 | 5.15 | 100 | 100 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 8 issues (= instructions) costing 4 points each. | 32 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►243 | exec | Inefficient vectorization. | 260 | 4.6 | 100 | 100 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 64 issues (= instructions) costing 4 points each. | 256 | ||||
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►203 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 273 | 4.35 | 96.15 | 91.11 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 48 issues (= instructions) costing 4 points each. | 192 | ||||
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 10 issues (= instructions) costing 4 points each. | 40 | ||||
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 6 issues ( = indirect data accesses) costing 4 point each. | 24 | ||||
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BLEND/MERGE, SHUFFLE/PERM, BROADCAST) - Simplify data access and try to get stride 1 access. There are 13 issues (= instructions) costing 1 point each. | 13 | ||||
| ○ | [SA] Inefficient vectorization: use of masked instructions - Simplify control structure. The issue costs 2 points. | 2 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►200 | exec | Inefficient vectorization. | 242 | 4.19 | 100 | 94.02 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 48 issues (= instructions) costing 4 points each. | 192 | ||||
| ○ | [SA] Presence of expensive instructions (GATHER/SCATTER) - Use array restructuring. There are 10 issues (= instructions) costing 4 points each. | 40 | ||||
| ○ | [SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BLEND/MERGE, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 6 issues (= instructions) costing 1 point each. | 6 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | [SA] Inefficient vectorization: use of masked instructions - Simplify control structure. The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►197 | exec | Inefficient vectorization. | 128 | 3.66 | 100 | 100 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 32 issues (= instructions) costing 4 points each. | 128 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 |