Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (37.78 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with compilation options informations and -fno-omit-frame-pointer is present
-fno-omit-frame-pointer improves the accuracy of callchains found during the application profiling.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 3.00 / 3 ] Most of time spent in analyzed modules (99.97%) comes from functions compiled with architecture specialization option -march=graniterapids
[ 3 / 3 ] Optimization level option is correctly used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 0 ] Fastmath not used
Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (95.44%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 98.50% of observed threads are actually active
[ 4 / 4 ] CPU activity is good
CPU cores are active 99.60% of time
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (6.52%), representing an hotspot for the application
[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (95.33%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 4 / 4 ] Affinity is good (99.71%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (2.12%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.11%) lower than cumulative innermost loop coverage (95.33%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 58 - exec | Execution Time: 6 % - Vectorization Ratio: 97.73 % - Vector Length Use: 49.15 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 5 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Inefficient Vectorization | 1 | |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ►Loop 229 - exec | Execution Time: 5 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 32 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 8 issues (= instructions) costing 4 points each. | 32 |
| ►Data Access Issues | 0 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ►Loop 60 - exec | Execution Time: 5 % - Vectorization Ratio: 98.08 % - Vector Length Use: 49.28 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 5 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Inefficient Vectorization | 1 | |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each. | 1 |
| ►Loop 70 - exec | Execution Time: 5 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 1 issues (= instructions) costing 4 points each. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Loop 107 - exec | Execution Time: 4 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 0 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ►Loop 177 - exec | Execution Time: 4 % - Vectorization Ratio: 77.78 % - Vector Length Use: 41.67 % | |
| ►Loop Computation Issues | 4 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ►Data Access Issues | 14 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 5 issues ( = data accesses) costing 2 point each. | 10 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 4 issues (= instructions) costing 1 point each. | 4 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 5 issues ( = data accesses) costing 2 point each. | 10 |
| ►Inefficient Vectorization | 4 | |
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 4 issues (= instructions) costing 1 point each. | 4 |
| ►Loop 116 - exec | Execution Time: 4 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 0 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ►Loop 74 - exec | Execution Time: 3 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 0 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ►Loop 82 - exec | Execution Time: 3 % - Vectorization Ratio: 100.00 % - Vector Length Use: 50.00 % | |
| ►Loop Computation Issues | 16 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ►Data Access Issues | 0 | |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each | 0 |
| ►Loop 75 - exec | Execution Time: 3 % - Vectorization Ratio: 16.39 % - Vector Length Use: 14.34 % | |
| ►Loop Computation Issues | 12 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 3 issues (= instructions) costing 4 points each. | 12 |
| ►Control Flow Issues | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 2 issues (= instructions) costing 1 point each. | 2 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points. | 12 |
| ►Inefficient Vectorization | 2 | |
| ○ | [SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 2 issues (= instructions) costing 1 point each. | 2 |