Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (21.03 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3.00 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g and -fno-omit-frame-pointer
-g option gives access to debugging informations, such are source locations. -fno-omit-frame-pointer improve the accuracy of callchains found during the application profiling.
[ 3 / 3 ] Optimization level option is correctly used
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 3.00 / 3 ] Architecture specific option -axCORE is used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (87.79%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] CPU activity is good
CPU cores are active 98.86% of time
[ 4 / 4 ] Threads activity is good
On average, more than 96.74% of observed threads are actually active
[ 4 / 4 ] Affinity is good (99.76%)
Threads are not migrating to CPU cores: probably successfully pinned
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (80.84%), representing an hotspot for the application
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (6.82%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 0 / 3 ] Cumulative Outermost/In between loops coverage (80.97%) greater than cumulative innermost loop coverage (6.82%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 2044 - exec | Execution Time: 80 % - Vectorization Ratio: 9.52 % - Vector Length Use: 13.10 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 1429 - exec | Execution Time: 3 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 4 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ►Loop 1691 - exec | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 4 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ►Loop 2277 - exec | Execution Time: 1 % - Vectorization Ratio: 6.25 % - Vector Length Use: 13.28 % | |
| ►Loop Computation Issues | 20 | |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each. | 16 |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ►Data Access Issues | 44 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 7 issues ( = indirect data accesses) costing 4 point each. | 28 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 42 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 7 issues ( = indirect data accesses) costing 4 point each. | 28 |
| ►Loop 1856 - exec | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 4 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ►Loop 2043 - exec | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Control Flow Issues | 16 | |
| ○ | [SA] Too many paths (10 paths) - Simplify control structure. There are 10 issues ( = paths) costing 1 point each with a malus of 4 points. | 14 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 16 | |
| ○ | [SA] Too many paths (10 paths) - Simplify control structure. There are 10 issues ( = paths) costing 1 point each with a malus of 4 points. | 14 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 1690 - exec | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.25 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ○Loop 1072 - exec | Execution Time: 0 % - Vectorization Ratio: 100.00 % - Vector Length Use: 25.00 % | |
| ►Loop 1428 - exec | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.51 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 15 | |
| ○ | [SA] Too many paths (9 paths) - Simplify control structure. There are 9 issues ( = paths) costing 1 point each with a malus of 4 points. | 13 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 2276 - exec | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.36 % | |
| ►Control Flow Issues | 4 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 44 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 7 issues ( = indirect data accesses) costing 4 point each. | 28 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 46 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each. | 14 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 7 issues ( = indirect data accesses) costing 4 point each. | 28 |
| ○ | [SA] Non innermost loop (InBetween) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |