options

exec - 2024-02-23 12:07:21 - MAQAO 2.19.1

Help is available by moving the cursor above any symbol or by checking MAQAO website.

Stylizer  

[ 4 / 4 ] Application profile is long enough (912.82 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 0 / 3 ] Some functions are compiled with a low optimization level (O0 or O1)

To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.

[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation information

Functions without compilation information (typically not compiled with -g) cumulate 100.00% of the time spent in analyzed modules. Check that -g is present. Remark: if -g is indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Architecture specific options are needed to produce efficient code for a specific processor ( -x(target) or -ax(target) ).

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.13 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

Optimizer

Loop IDModuleAnalysisPenalty ScoreCoverage (%)Vectorization
Ratio (%)
Vector Length
Use (%)
246execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.6916.1481.8822.24
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 6 issues (= instructions) costing 4 points each.24
[SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points.20
[SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BLEND/MERGE, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 19 issues (= instructions) costing 1 point each.19
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each0
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
Warning! Some static analysis are missing because the loop has too many paths. Use a higher value for --maximal_path_number option.0
199execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.8912.580.8622.34
[SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BLEND/MERGE, SHUFFLE/PERM) - Simplify data access and try to get stride 1 access. There are 25 issues (= instructions) costing 1 point each.25
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 6 issues (= instructions) costing 4 points each.24
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 9 issues ( = arrays) costing 2 points each18
[SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 2 issues ( = indirect data accesses) costing 4 point each.8
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Several paths (4 paths) - Simplify control structure or force the compiler to use masked instructions. There are 4 issues ( = paths) costing 1 point each.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
[SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points.2
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each.2
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
1039execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.1939.8392.1423.88
[SA] Too many paths (128 paths) - Simplify control structure. There are 128 issues ( = paths) costing 1 point each with a malus of 4 points.132
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 12 issues (= instructions) costing 4 points each.48
[SA] Presence of special instructions executing on a single port (INSERT/EXTRACT, BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 5 issues (= instructions) costing 1 point each.5
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points.2
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 0 issues ( = arrays) costing 2 points each0
Warning! Some static analysis are missing because the loop has too many paths. Use a higher value for --maximal_path_number option.0
257execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.168.6239.3317.42
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 7 issues ( = data accesses) costing 2 point each.14
[SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each.2
318execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.1057.0195.2824.41
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 14 issues (= instructions) costing 4 points each.56
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 14 issues ( = arrays) costing 2 points each28
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 5 issues ( = data accesses) costing 2 point each.10
[SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 5 issues (= instructions) costing 1 point each.5
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
210execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.126.1151.4918.87
[SA] Too many paths (8 paths) - Simplify control structure. There are 8 issues ( = paths) costing 1 point each with a malus of 4 points.12
Warning! Some static analysis are missing because the loop has too many paths. Use a higher value for --maximal_path_number option.0
179execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.754.798.3124.79
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 14 issues ( = arrays) costing 2 points each28
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 10 issues ( = data accesses) costing 2 point each.20
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each.16
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
[SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points.2
[SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points.2
[SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each.1
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
383execInefficient vectorization.304.4910025
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each.16
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 4 issues ( = arrays) costing 2 points each8
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
188execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.633.4898.4124.8
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 14 issues ( = arrays) costing 2 points each28
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 10 issues ( = data accesses) costing 2 point each.20
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 2 issues (= instructions) costing 4 points each.8
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
[SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each.1
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
176execPartial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access.632.7197.6724.71
[SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 14 issues ( = arrays) costing 2 points each28
[SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 4 issues (= instructions) costing 4 points each.16
[SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 6 issues ( = data accesses) costing 2 point each.12
[SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points.4
[SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points.2
[SA] Presence of special instructions executing on a single port (BLEND/MERGE) - Simplify data access and try to get stride 1 access. There are 1 issues (= instructions) costing 1 point each.1
Warning! There is no dynamic data for this loop. Some checks can not been performed.0
×